Chia Sẽ Kinh Nghiệm Về IT



Tìm Kiếm Với Google
-


Gởi Ðề Tài Mới  Gửi trả lời
 
Công Cụ Xếp Bài
Tuổi 22-09-2009, 02:28 PM   #1
hoctinhoc
Guest
 
Trả Lời: n/a
Thêm Ổ Cứng Vào Máy Tính Linux (Add an Additional Disk Drive to Your Linux Computer)
Thêm Ổ Cứng Vào Máy Tính Linux (Add an Additional Disk Drive to Your Linux Computer)


IDE drives are referred to as hda for the first drive, hdb for the second etc...IDE uses separate ribbon cables for primary and secondary drives. The partitions on each drive are referred numerically. The first partition on the first drive is referred to as hda1, the second as hda2, the third as hda3 etc ...
Linux IDE naming conventions:



Device Description Configuration /dev/hda 1st (Primary) IDE controller Master /dev/hdb 1st (Primary) IDE controller Slave /dev/hdc 2nd (Secondary) IDE controller Master /dev/hdd 2nd (Secondary) IDE controller Slave

Note: SCSI disks are labeled /dev/sda, /dev/sdb, /dev/sdc etc... to represent the first, second, third,... SCSI hard drive devices but not the SCSI ID. SCSI hard drive partitions are represented by an additional number. i.e. First drive first partition, /dev/sda1, second partition, /dev/sda2,... Other SCSI devices such as tape backup are labeled /dev/st0 for the first, /dev/st1 for the second and so forth. See YoLinux SCSI tutorial for more info.





Command and Response Dialog of Adding a New IDE Drive:

As root perform the following: (as highlighted in bold)



[root]# fdisk /dev/sdc
Command (m for help): m (Enter the letter "m" to get list of commands)
Command action
a toggle a bootable flag
b edit bsd disklabel
c toggle the dos compatibility flag
d delete a partition
l list known partition types
m print this menu
n add a new partition
o create a new empty DOS partition table
p print the partition table
q quit without saving changes
s create a new empty Sun disklabel
t change a partition's system id
u change display/entry units
v verify the partition table
w write table to disk and exit
x extra functionality (experts only)

Command (m for help): n
Command action
e extended
p primary partition (1-4)
e
Partition number (1-4): 1
First cylinder (1-2654, default 1):
Using default value 1
Last cylinder or +size or +sizeM or +sizeK (1-2654, default 2654):
Using default value 2654

Command (m for help): p

Disk /dev/hdb: 240 heads, 63 sectors, 2654 cylinders
Units = cylinders of 15120 * 512 bytes

Device Boot Start End Blocks Id System
/dev/hdb1 1 2654 20064208+ 5 Extended

Command (m for help): w (Write and save partition table)

[root]# mkfs -t ext3 /dev/sdc1
mke2fs 1.27 (8-Mar-2002)
Filesystem label=
OS type: Linux
Block size=4096 (log=2)
Fragment size=4096 (log=2)
2508352 inodes, 5016052 blocks
250802 blocks (5.00%) reserved for the super user
First data block=0
154 block groups
32768 blocks per group, 32768 fragments per group
16288 inodes per group
Superblock backups stored on blocks:
32768, 98304, 163840, 229376, 294912, 819200, 884736, 1605632, 2654208,
4096000

Writing inode tables: done
Creating journal (8192 blocks): done
Writing superblocks and filesystem accounting information: done

This filesystem will be automatically checked every 34 mounts or
180 days, whichever comes first. Use tune2fs -c or -i to override.
[root]# mkdir /opt2
[root]# mount -t ext3 /dev/sdc1 /opt2


Note: A computer system may have multiple drives with primary partitions but only one primary partition may be active on one drive only. The active primary partition is used for booting the system and is referenced by the Master Boot Record (MBR). Each hard drive may only have a maximum of four primary partitions. One may only boot an OS from a primary partition. Extended partitions allow one to place up to 24 partitions on a single drive.
The above example shows the addition of a drive as one whole extended partition used to extend the storage space of the system. It was not created to hold additional operating systems as this would require a primary partition. Primary partitions can be used to extend the storage space of the system as well. It is not precluded from such a function but it will then limit you to four partitions for that hard drive.




File: /etc/fstab



Enter the drive into the fstab file so that it is recognized and mounted upon system boot.



File: /etc/fstab Red Hat 8.0
LABEL=/ / ext3 defaults 1 1
LABEL=/boot /boot ext3 defaults 1 2
none /dev/pts devpts gid=5,mode=620 0 0
none /proc proc defaults 0 0
none /dev/shm tmpfs defaults 0 0
/dev/hda2 swap swap defaults 0 0
/dev/sdc1 /opt2 ext3 defaults 1 2
/dev/cdrom /mnt/cdrom iso9660 noauto,owner,kudzu,ro 0 0
/dev/fd0 /mnt/floppy auto noauto,owner,kudzu 0 0

The digits "1 2" refer to whether the mount point should be backed up when the dump command is used and disk integrity checks using fsck. The "1" states that it should be backed up when the dump command is issued (0=no). The "2" refers to the order in which "fsck" should check the mount points. The digit "1" identifies the root ("/") of the filesystem. All others should be "2". (0=no check)

  Trả lời ngay kèm theo trích dẫn này
Gửi trả lời


Công Cụ
Xếp Bài

Quyền Hạn Của Bạn
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is Mở
Hình Cảm xúc đang Mở
[IMG] đang Mở
Mã HTML đang Tắt




Bây giờ là 04:29 AM. Giờ GMT +7



Diễn đàn tin học QuantriNet
quantrinet.com | quantrimang.co.cc
Founded by Trương Văn Phương | Developed by QuantriNet's members.
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.